How to Install a Pedestal Bathroom Vanity

Pedestal bathroom vanities were originally made of enameled cast iron, but by 1915 manufacturers began fabricating them from vitreous China, a glass-like porcelain. For all their stylish attributes, pedestal sinks present some installation challenges. Drain and supply pipes must be roughed in at the right height. Completed pipe work has to look neat. And looming at every turn is the dreaded crack, the sound porcelain makes when a fastener is tightened too much - and the porcelain breaks. Don't rely on the manufacturer's instruction sheet. floor. After the holes have been marked, remove the sink from the area. Install the lag screws into the wood backing behind the wall. Ensure your bit is at least a size smaller than the lag bolts so they'll hold tight in the wall. Drill two 1/4" holes for the hanger bolts at the marks on the wall. Thread the hanger bolts into the wall. Leave approximately 1-1/4" of each bolt exposed between the cap nuts and the finished wall.The pedestal sink must be mounted to the floor for stability. The technique for doing this will vary depending on the type of floor

First choose your sink, then hire a plumber to rough in a new waste pipe. "More often than not, the existing waste pipe is too low to install the trap, which fits inside the pedestal. First things first shut off the water at the main. Turn the water heater to "off," or turn the switch to the "pilot" position if it's gas. Drain the plumbing by opening a faucet. Remove the old sink and trap. Take off the old lavatory stops. The plumbing for a pedestal sink is exposed, so all of the plumbing, including the stops need to be new. It will also be necessary to install a new chrome lavatory stop and escutcheon cover.Using two adjustable wrenches, remove the old supply stops from the hot and cold water lines, and then remove the old escutcheon covers. Apply Teflon tape on both stub outs, and then add new escutcheon covers by sliding the cover over the roughed in water supply. Thread new supply stops on both and use a wrench to tighten everything up. Ensure that the inlet valve is in the upright position. Unscrew the old collar nut, and then slide the new p-trap escutcheon cover over the drain hole. Place the lavatory on the pedestal, and then set it in the desired location. Make sure the lavatory is level. Be sure to center the pedestal to the drain hole on the wall. Once the pedestal is centered, use a pencil to mark where the sink will sit against the wall.Use a pencil to mark where the anchor holes will be drilled in the wall and

• For drilling into concrete, use a hammer drill and a concrete bit. Simply add a lag screw, and then snug it down with a ratchet. Be sure not to over-tighten. 

• For drilling into tile, use a tile bit to drill the holes. A tile bit has a head like an arrowhead. Drill into the grout line if possible to prevent damage to the tile.

Note: Don't apply sealant around the base of the pedestal. It could damage the floor if the sink ever needs to be moved. "Dressing" the sink means to put all of the hardware on the sink before installation.

Install the spout and handles use a roll of plumber's putty around the seal to make sure it's water tight. Insert the valve bodies into the proper mounting holes, ensuring that the valve body marked "cold" is installed to the right of the center hole. Once the valve body is in place, slide the metal washer and nut onto the base, and then tighten it down. Place the seal ring over the spout body, and then insert the spout into the sink.

Place the metal washer and nut onto the spout shank and tighten the nut with a wrench. Install the hot water valve the same way as the cold water valve. Don't forget to use plumber's putty.With the hardware mounted on the top side of the sink, mount the supply lines underneath the sink. Screw the supply tee to the bottom of the spout, and then tighten it up with a pair of slip joint pliers. Attach the flexible supply lines to the hot and cold valve bodies, and then attach them to the supply tee. Connect both the hot and cold flexible supply lines to each of the valve bodies, tightening each one with a wrench. Apply a generous amount of plumber's putty around the base of the flange, and then place the flange in the sink. Place the nylon o-ring and nut over the flange. Tighten with slip-joint pliers. Attach the drain body to the flange, ensuring a tight seal. Use Teflon tape around the threads of the tailpiece to prevent the drain assembly from leaking. Screw the tailpiece to the drain body. Attach the connecting rod to the drain body, and then connect the stopper rod from the back of the faucet to complete the drain assembly. Set the lavatory on the pedestal so that the hanger bolts extend through the lavatory holes. Install the cap nuts and washers, and then tighten. With the sink mounted, connect both the hot and cold water connections. Tighten with slip-joint pliers. Secure the end of the p-trap to the tailpiece of the drain assembly. Connect the p-trap to the tailpiece by screwing it into place using the threaded connection. Turn the water on at the main. Turn on the water heater. Open the faucet at the new sink, and then check for leaks. If there are leaks you should shut the water supply of again, and go back to recheck all of your original work. Making sure everything is tightened securely. After checking everything over again, turn the water supply back on. Your pedestal bathroom vanity should be in full working order. For further information contact a bathroom specialist at Bath Trends USA. 

For more updated information about pedestal bathroom vanity , modern pedestal bathroom vanities please  visit us our website : https://www.bathtrendsusa.com/index.php/bathrooms/bathroom-vanities/pedestal.html

What Should I Know About Pedestal Bathroom Vanities?

What comes around, goes around--that pretty much describes pedestal bathroom vanities. After occupying a familiar place in bathrooms for many years, pedestals gradually fell out of fashion. Now, they are surging back in popularity and can be found in many homes.  But why have these vintage basins suddenly grabbed the attention of modern homeowners? Pedestal sinks are composed of two pieces: the pedestal and the sink basin.The wall behind the intended location must be strong enough to support significant weight. Many homeowners are surprised to learn that pedestal sinks are largely supported by the wall, not the pedestal. Not only that, the supply and drain pipes enter the sink from the wall rather than the floor.
These are some of the most common places for pedestal vanities. Don't feel limited by the following list; you're welcome to put your pedestal sink wherever you want. But you do tend to find them most commonly in these applications:
• In half-baths and powder rooms.
• Any bathroom where space is limited.
• When you need to control remodeling costs.
• Houses that aim for a period style.
• When you prefer do-it-yourself installation.
• When you have a small vehicle or any kind of difficulty transporting large bathroom cabinets. Pedestal sinks come in two pieces and are easily transported even in small vehicles.

Inexpensive pedestal sinks are available. After all, there isn't much to it: a basin, a pedestal, and that's it.You can easily find pedestal sinks ranging from about $60 up to $500 and more. Professional installation of pedestal sinks will, on a national average, cost $713.

DIY installation will cost considerably less: $417. Read the product description carefully, or you might end up with the pedestal only. Products described as sink pedestal are not the same as pedestal sink. Just switching those two words around makes all the difference in the world. The same token, watch out for the term basin only. It's safe to say that anything under $50 is not a complete pedestal + basin combination. If the typical white vitreous  pedestal sink is what comes to your mind, you might be interested to hear that there are a number of varieties out there. Square pedestal sinks can provide more apron around the basin to make up for the loss of counter space. It's even possible to find glass pedestal sinks that have translucent pedestals to hide the supply and drain lines.
Pros
Beauty is in the eye of the beholder, but most homeowners say that they like the looks of pedestal sinks. So, it's appropriate that this is the first advantage of a pedestal sink:
• Attractive and streamlined.
• Lets you show off your entire bathroom (wall, baseboard, floor, etc.) instead of hiding these features with a boxy base cabinet.
• Instant period decor if you have or are trying to achieve a classic or traditional style.
Cons
While lovely, pedestal sinks tend to get low marks for practicality:
• No counter space available; just the sink apron.
• Any bathroom where space is limited.
• Requires bracing on the wall behind the sink. With sinks dropped into base cabinets, you can get by with no bracing at all.
• If replacing a base cabinet with a pedestal sink, most likely you will have significant work to do to improve your bathroom flooring, baseboard, and wall. In most cases, these areas will be downright ugly. In the worst-case scenario, flooring and baseboards may not even exist.
Pedestal bathroom vanities are a beautiful addition to any bathroom, and can really save space when needed. Please call Bath Trends USA at 1-800-413-2701.

Should I get a White Pedestal Bathroom Vanity?

When you start remodeling your bathroom you may get stuck in a rut when choosing your vanity. A white pedestal bathroom vanity can be a safe, and easy choice. If you get a custom pedestal sink, with a colorful basin, or a specific material it can be difficult to make changes later without replacing the entire vanity again.

No one wants to remodel their entire bathroom just to be able to change the color of the paint. When you choose a white pedestal bathroom vanity this won't be a problem years down the road, and you'll have the freedom to make small changes that make a big difference. There are several reasons to choose a white pedestal sink. One of the most obvious reasons is space. If you have a small bathroom pedestal sinks are a great way to give you room to roam in your bathroom. Another reason is, white pedestal sinks are practical and match anything. Kitchen sinks not only have to accommodate pots and pans but also have to withstand the beating that these items regularly inflict on sink basins. By contrast, bathroom sinks only have to be big enough to fit a pair of hands comfortably and durable enough to withstand hot tap water. Because of this limited purpose, manufacturers have been free to develop a dizzying array of designs, which can make choosing a bathroom sink as much a beautiful decision as a practical one. Even so, most bathroom sinks come in a handful of basic styles, each of which has pros and cons.A pedestal sink is the perfect choice for a small bathroom.  They take up very little space and instead put the extra space into the room, making it appear larger than it is.  However, storage is always an issue.  They typically provide very little storage, thus requiring other creative options such as built-in wall cabinets, baskets and other cabinetry.  Pedestal Sinks come in a variety of colors, shapes and sizes.  However, vanities have just as many (if not more) options, including finish and storage options.  A style to fit your décor can be found in either style.  Cleaning and maintenance of pedestal sinks are typically easier to keep clean and maintain. Whichever you choose, the chic white pedestal bathroom vanities at Bath Trends USA are inspiration for a swoon-worthy bathroom!